Electro-cam PS-6144 Series Manual de usuario Pagina 96
- Pagina / 112
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6-24 Communications
Motion ANDing
40332 Channel Index
Read/write
Values: 1 - Max Channel Number
Channel index for the Motion Enable Level Register.
40333 Motion Enable Level
Read/write
Values: 0 = Off, n = Motion Detection Level
Specifies the motion detection level used for a channel.
Output Enable ANDing
40334 Output Enable Index
Read/write
Values: 1 - Max Channel Number
Channel index for the Output Enable register.
40335 Output Enable
Read/write
Values: 0=Channel not ANDed, 1=Channel ANDed
Specifies whether a channel is ANDed with the Enable Input.
Group Programming
40336 Group Quantity
Read/write
Values: 1 - 6
Specifies the number of output groups.
40337 Group Index
Read/write
Values: 1 - 6
Group index for Channel Quantity and Group Mode Registers.
40338 Channel Quantity
Read/write
Values: 0 - n
Defines the number of channels in the output group specified by the Group Index Register.
40339 Group Mode
Read/write
Values: 0 - 5
Defines the operating mode for the output group specified by the Group Index Register. Note
that groups in mode '0' do not need (or have) an enable input.
Run Time Control
40340 Stop Control
Read/write
Values: 0 = Running, 1 = Stopped
When PLuS is STOPPED, changes written to registers do not update the checksum in
EEPROM memory. Changes are faster when unit is stopped, but you must read from the
Checksum Register when changes are complete to establish a valid checksum. Writing a '1'
value to this register will place the PLuS in STOPPED mode. Writing a '0' to this register will
restart the PLuS via a watchdog timer reset.
40341 EEPROM Checksum
Read only
Returns the current checksum of EEPROM memory. If computed checksum of EEPROM
memory does not match the current value (i.e. if changes were made while unit STOPPED),
a new value will be written to EEPROM memory.
Registers (Cont'd)
- PS-6144 Series 1
- Table of Contents 3
- Mechanical Cam Switches 5
- Programmable Limit Switches 5
- PS-6144 Description 6
- Basic Terminology 7
- PS-6144 Standard Features 7
- PS-6144 Optional Features 8
- General Mounting & Wiring 9
- PGM:1 RPM:1500 10
- MENU< POS: 180 10
- 2-3 Installation & Wiring 11
- 2-4 Installation & Wiring 12
- Controller Input Wiring 13
- 2-6 Installation & Wiring 14
- 2-7 Installation & Wiring 15
- Output Wiring 16
- Output Wiring (cont’d) 17
- Keypad Wiring 20
- DIP Switch Configurations 21
- Communications Wiring 23
- Resolver Installation 24
- Resolver Dimensions 25
- Resolver Cables 26
- Output Transistor Replacement 28
- Menu Tree 30
- Initial Programming 31
- OFFSET 3-16 31
- Analog Module Numbe 32
- Analog High RPM 32
- Analog Offset 32
- Number of Analog Output 33
- Communications 34
- Channel Copy 34
- Communications (Cont’d) 35
- Default Program 35
- LEVEL: OPERATOR 36
- PASSWORD: 1234 36
- Password Number 36
- View Program 37
- --- --- --- Program 37
- Enable Codes (cont’d) 37
- GROUP POSITION 38
- DISPLAY: EACH< 38
- Machine Speed 39
- Active Program 39
- Keyboard Quantity 40
- Input Status 40
- Motion ANDing 42
- Memory Tests 42
- Motion detection leve 43
- High RPM setpoint 43
- Low RPM setpoint 43
- Value for this Group 44
- 3-17 Programming 45
- Output Enable ANDing 46
- Output Groups 46
- Output Groups (Cont’d) 47
- Output Status 47
- Password 48
- Output Status (Cont’d) 48
- Password (Cont’d) 49
- Per Channel Enable 49
- Program Copy 49
- Pulse Copy 50
- Program Select Mode 50
- Pulse Copy (cont’d) 51
- Rate Setup 52
- SCALE 53
- FACTOR: 360< 53
- Program to view or modify 54
- Setpoints (Cont’d) 55
- CH:1 EDG 55
- Output Channel 56
- Speed Compensation (cont’d) 57
- Speed Comp Mode 57
- Timed Outputs 58
- Toggle RPM 58
- 4-1 Speed Compensation 59
- Standard Speed Comp 60
- Standard Speed Comp (Cont’d) 61
- Leading Trailing Speed Comp 62
- 4-5 Speed Compensation 63
- Speed Comp Guidelines 64
- Negative Speed Compensation 64
- Mode 1 Operation 67
- Mode 0 Operation 67
- Mode 2 Operation 68
- Mode 1 Operation (Cont’d) 68
- Mode 2 Operation (Cont’d) 69
- Mode 3 Operation 69
- Mode 4 Operation 70
- Mode 3 Operation (Cont’d) 70
- Mode 4 Operation (Cont’d) 71
- Mode 5 Operation 71
- Mode 5 Operation (cont’d) 72
- 6-1 Communications 73
- PLuSNET II Program (cont’d) 74
- 6-3 Communications 75
- Serial Commands 76
- Serial Commands (cont’d) 77
- Output group offset value 80
- Shaft position offset 80
- Checksum 84
- Error Codes 84
- 6-13 Communications 85
- 40279 Offset Mapping 86
- Motion Detection 86
- 40289 Analog High RPM 86
- Quick Reference 86
- 40310 Analog Quantity 87
- Discrete I/O 88
- Registers 89
- Registers (Cont'd) 90
- 40280 Group Index 91
- 40281 Group Offset 91
- 40288 Analog Offset 92
- 40308 Shaft Position 93
- 40309 Shaft Offset 93
- Bit 5: Motion detection 95
- Special Functions 98
- Controller Diagnostics 99
- Keypad Diagnostics 100
- ERROR: RESOLVER 101
- NOT CONNECTED! 101
- General Troubleshooting 102
- 7-5 Troubleshooting 103
- Fuse Part Numbers 104
- PS-6144 Controller Specs 105
- A-2 Appendix 106
- Resolver Specifications 107
- Factory Defaults 107
- A-4 Appendix 108
- Access Codes, Entering 3-20 109
- Analog Output 3-4 109
- Group Position Display 3-10 109
- Offset, Analog Output 3-4 110
- I-3 Index 111
- PRINTED IN U.S.A 256 10/01 112
Relacionado con productos y manuales para Routers Electro-cam PS-6144 Series
Routers Electro-cam 5000 Series Manual de usuario
(80 paginas)
(80 paginas)
Routers Electro-cam PL-1746 Manual de usuario
(8 paginas)
(8 paginas)
Routers Electro-cam PL-1746 Series Manual de usuario
(146 paginas)
(146 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales